First Time Setup
Connect the ethernet socket of your Zone to a network switch using a standard CAT5/6 cable. If you have a WiFi router connected to this network switch, you will be able to access wirelessly. Your device and the Zone must be on the same network.
Alternatively, you can connect a computer or laptop directly for setup purposes only.
- The factory network configuration of Zone is DHCP. When connected to a DHCP server it will be assigned a DHCP address from that server. E.g. a 192.168.8.1 gateway on subnet 255.255.255.0 will assign the Zone an IP of 192.168.8.x.
If no DHCP server is present it will stop after five attempts after which it will assign an Automatic Private IP Address (APIPA) of the form 169.254.x.x on subnet 255.255.0.0. - Successful network connection will be signified by the Power LED on the front panel of the Zone showing white. If the Power LED is green, check your network connection.
- In your browser type the mDNS address http://optimalaudio.local
- Some devices do not support mDNS in which case you will need to use the IP address in your browser. If your network is configured correctly, you will already know the first three octets of the IP address.
-
To view the last octet of the IP address of the unit, hold down the two 'All Zones" buttons on the front panel simultaneously. The LEDs on the rotary controls below will indicate the last three digits of the IP address - as shown in the image below. In the latest WebApp release, Source buttons 1 and 2 will also indicate if the Zone is in DHCP or Static IP respectively.
A Zone 4P showing the last octet of .123 on a Static IP address
Recommended setup
Once you have connected to WebApp for the first time, it is recommended that you set a static IP address for the Zone and turn off DHCP.
In WebApp, Navigate to the Network page - Settings > System > Network, where you can assign the necessary network settings. Be sure to untick Use DHCP when assigning your own IP address and click Save Settings at the bottom of the page to finalise this step.
You can also assign a custom mDNS 'friendly' name for your Zone in network settings. This is recommended if you have two Zone controllers on the same network or you wish to set a custom name appropriate to the installation.
For the most reliable setup, it is recommended that Zone is installed alongside other networking hardware such as a router, to distribute IP address across the network, and a network switch, to allow other Ethernet devices to connect to the same network.
The router can serve the entire building or just the Zone, depending on the level of network security required. It is not essential that the router is connected to the internet, unless using third-party streamers.
Below are multiple options for network configuration. Option 3 should only be used when configuring a Zone 'out of the box'.
Troubleshooting
If the unit has been set to a static IP address and this is not known, DHCP can be forced back on by holding the "FUNC" button on the Zone rear panel during start-up. As the unit boots, the power light will cycle between white and green lights to show that this network configuration change has taken place.
If the unit is set to DHCP and no server is available, a static IP address can be forced in the same way. Hold the "FUNC" button during start-up and an IP address of 192.168.1.250 will be set.
This will allow access to the unit from devices on the same subnet (255.255.255.0). Once connection has been established, settings can be chosen correctly in the Network page.
If you are running the latest version of WebApp, a system information file name "sysinfo.txt" is created on the SD card with the current network settings - IP address, MAC address and mDNS name.
To access this file, remove the SD card from the Zone and insert it into your computer. The file will be available in the root folder and will open in your computer's text editor with the following details.
Network Diagnostic Tool
We are currently in the process of developing a Network Diagnostic Tool application for Windows and Mac users that will allow easier troubleshooting. We are currently in the beta testing phase with a full release due in Q4. If you are having connection issues with your Zone, please contact our support team and we may be able to send the beta version to you.
Important - the Network Diagnostic Tool requires a Zone to be running the latest version of WebApp (1.6.4) as a minimum requirement. It will not detect Zones on earlier WebApp versions. Please update your firmware before contacting us.